Automatic Urinal Flusher KEG-1066AD

    • Wall Mounted Automatic Sensor Urinal Flusher KEG-1066AD

    The Automatic Sensor Urinal Flusher KEG-1066AD is wall mounted installed on the wall, with an infrared sensor on top of the steel panel, when people stand in front of the auto flush valve, the sensor detects and active 2s pre-flush, and 6s Flush automatically after leaving.

    With a press button under the sensor, even when the sensor is no power, you can still press the button to activate manual flush.

    • Brand: KEGE
    • Item No: KEG-1066AD
    • 2s for pre-flush & 6s for after-flush
    • Automatically flush if no usage in 24 hours
    • Hygienic, bacteria and germs free without touching
    • Manual button on the face panel
    Require samples
    Contact us for prices

    Features:

    • Automatic on/off: when you stand in front of the auto urinal flush, 2s pre-flush after detection; 6s Flush automatically after leaving.
    • Automatically flush if no usage in 24 hours.
    • Low power indication: This may indicate it is time to replace existing batteries with new ones or there is not enough power going to the unit.
    • Water-saving: Water-efficient flusher valve reduces overall water usage without sacrificing water.
    • Energy-saving: 4AA alkaline batteries shall last approximately 3000 times/month for 1.5 to 2 years.
    • Installation of concealed wall type, straight up and down, suitable for wall installation above 10cm thick.
    • Healthy and Safe: Touch free, it can prevent the spread of bacteria and germs, convenience and hygiene.
    • Stainless steel panel and box, all copper solenoid flush valve: electronic part seal design, waterproof and moisture-proof.
    • Filter device: The filter can be removed and clean to prevent blocking. The solenoid valve is protected by anti-blocking needle inside.
    • Equipped with manual button to prevent the sensor from being damaged and unable to be used.
    Auto Urinal Flusher Valve KEG-1066AD size
    Urinal auto flush structure
    Auto Urinal Flusher Valve KEG-1066AD installation diagram

    Auto Urinal Flusher Valve KEG-1066AD Specification
    External Power Supply Applicable water pressure Applicable Water Temperature Ambient Temperature Feedwater caliber Flushing water volume

    4XAA batteries

    		 AC:110v-240V,50Hz-60Hz DC&AC combined 0.05-0.7Mpa 0.1-60℃ 0.1-45℃ G1/2” 1.5-4L(10s based on water pressure of 0.3-0.6Mpa)

    INDUCTIVE URINAL FLUSH SENSOR KEG-K1066

    As the most important part, the work of the sensor is to forward the signals to the valve to turn on the urinal flusher after detecting your body. Its job is to inform the valve when to turn on or off the water when your body comes and leaves. The cover of the sensor is made of plastic ABS or PA and there is an electronic circuit board inside the sensor eye which also includes the led light.

    The sensor rang and flushing time can be adjusted by a remote controller. It washes automatically every 24 hours to avoid the peculiar smell caused by water drying in the water trap.

    Automatic Urinal Flush Sensor KEG-K1067

    Kege have about 50 types of the different sensor head for the selection. We can also customize the sensor cover according to your products.

    How to install automatic urinal flush?

    Auto urinal valve installation step1

    STEP1

    Dig a suitable hole on the wall according to the installation instruction. Inter control box into the wall and connect the inlet pipe and outlet pipe. Open the stop valve to ensure all the connectors are watertight.

    Notice:
    The distance between the housing surface and the ceramic tiles should be longer than 15mm.

    Auto urinal valve installation step2

    STEP2

    Adjust the position of the control box, fixed with pieces of wood or other fillers. Then cover the control box by protecting the board to avoid the solenoid valve be damaged when filling the cement around the control box. Finally, laying the tiles.

    Notice:
    The protecting board should be taken down when finished.

    Auto urinal valve installation step3
    Auto urinal valve installation step4
    Auto urinal valve installation last step

    STEP3

    1. A wire connected to the 220V power source should be laid before placing the control box into the wall.
    2. Connect the connectors as shown right, place the power supply box as figure 1 shows.
    3. Connect the power supply box to the power source.
    4. Fix the auto urinal flush face plate on the control box.

    Notice:
    Please shut off the power source during the installation.

    Touchless Urinal Flusher Valve Troubleshooting
    Problem Possible Reason Suggested Solution
    No water flow Batteries run out Replace batteries
    Dirt on sensor surface Clean the sensor surface
    Main water supply is shut off Turn main water supply on
    Dirt on water filter net Clean the water filter net
    Water pressure is not applicable Refer to technical specification
    Have a continuous water flow problem Batteries run out Replace batteries
    Low water pressure Refer to technical specification

    People who are asking more:

    Automatic urinal flusher uses infrared sensor technology that when you stand in front of urinal ceramic, the sensor detects and gives a pulse signal to the solenoid valve to open and give 2s pre-flush, then stop. After you leave, again 6s flush automatically. Program control all the process.

    For more details, please view here.

    Auto urinal flushers need electricity for sure. Both the sensor and solenoid valve works need electricity power. Normally DC: 4xAA alkaline 6V batteries.

    6V with 4xAA alkaline batteries shall last approximately 3000 times/month for one year.